You might need a few of the NAS1149F0316P ultra-thin washers to fine tune the center “knee” joint fit on most of the Cessna airplanes. They are not included in the kit.

It is very important to maintain proper torque for the bolts that clamp the chrome bushing/spacer at the upper attachments to the steering collar and the lower attachment to the nose gear strut. It is commonly thought that the chrome bushing/spacer is kept in position by the bolt filling the center bore of the bushing/spacer. This is not correct as the inner bore of the chrome bushing/spacer and the bolt are a loose non-precision fit. The bushing/spacer is secured by the bolt end, clamping the spacer so that it is tight between the arms of the aluminum forgings. Any looseness of this end clamp will allow movement of the chrome bushing/spacer. This movement will erode the aluminum forgings and create more free motion of the torque link.

 

All shimming of the torque links must be done with proper torque on the bolts. Periodically and during nose gear inspections, check the torque on the upper and lower torque link bolts. If the chrome bushing/spacer is allowed to move, the resultant wear can require replacement of the expensive aluminum forgings. McFarlane is working on a repair for the worn aluminum forgings. Unlike our competitors, extra care is given to the machining of the McFarlane chrome bushing/spacers to give the largest possible bearing surface to the ends that bear against the aluminum forgings. Chamfers or bevels are kept very small.

Strut seal leaks and flat struts can be caused by roll or twist of the main O-ring seal. It is very frustrating to carefully check all the parts and surfaces and put a new seal kit in the strut only to find it flat again after a relatively short time. We have seen this happen when a film of MIL-5606 hydraulic fluid dries out on the exposed chrome strut shaft. MIL-5606 by nature has a tendency to get sticky as it is exposed to air and dirt and then dry.

 

Very slight dried oil films are sometimes hard to detect and they can get past the plastic wiper seal. When this happens the sticky strut has a tendency to grab the O-ring and roll or twist it when the strut slides in or out causing the seal to distort. A very small O-ring twist or distortion will cause a leak. This phenomena is aggravated by the low pressure that the Cessna strut is designed for. Wipe the chrome strut down with Stoddard solvent (mineral spirits) periodically to soften and remove any dried oil film, dirt, dust and bugs.

Removing the flanged bushings from the torque link forging can be difficult as there is not a good surface to press against or grab onto. An easy way to remove them is to thread them with a tap, screw a bolt in the thread you made, and then drive or press against the bolt. The thread does not have to be a full depth thread for the bolt to hold securely in the bushing. The bushing material is somewhat hard, but not so hard that a standard hardware store tap will not do the job. Use cutting oil on the tap to prevent tap damage. Normally the bushing will then come out easily.

 

For stubborn bushings, soak the link assembly in boiling water before pressing the bushing. The heat will expand the aluminum forging more than the steel bushing. This helps loosen the press fit while limiting the temperature to prevent from overheating and harming the heat treat of the aluminum forging. A controlled oven can be substituted for boiling water as a heat source, but do not exceed 350° F. Do not use flame or other non-controlled heat sources.

 

An alternate method is to put dry ice in the bushing before driving or pressing on the bolt you threaded into the bushing. Do not over-press or hammer as the aluminum can gall to the bushing and leave a damaged bushing bore. If the bushing does not come out with light to moderate force take the time to use some heat or cold to help.

There are many components all connected to keep the nose gear in line. If one component is worn or out of tolerance it can cause shimmy problem. Reference Dave McFarlane’s article: Can You Stop Nose Gear Shimmy instructions and suggestions.

 

Overlooked items also include the rod ends, shimmy dampener mounting and attachment, shimmy dampener, and steering collar. The steering collar is where the steering rod tubes connect and the upper torque link is attached to, along with the shimmy dampener on most aircraft. If the steering collar has play vertically and laterally and is allowed to tilt; that will cause excessive wear and force on the torque links, steering, and strut components. There are three different thicknesses of shims to help get the collar in place.

 

Ensure that the shimmy dampener is working properly with no dead spots in dampening action. The cylinder could be worn on the inside or on a piston that warrants replacement of components. All of the nose strut components are tied to each other and any movement is transmitted through to the tire and back through the dampening system, which if remedied will continue to be more pronounced.